We have stumbled on this post relating to How to Install a Bathtub Yourself listed below on the net and reckoned it made sense to talk about it with you on my blog.
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough task. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall to eliminate the old bathtub and place the brand-new tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as set in the new one. Make certain you have actually certified yourself for the task and also are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is far better to think about utilizing one before you begin. Chances are you might need a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bath tub in your washroom if you have actually currently gotten a brand-new tub as well as don't need to change the setup of your previous water supply pipes.
Your devices as well as material list need to make up the following:
Preparing for the Installment
First of all, the supporting structure supplied with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its last position.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly troublesome due to the restricted access that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the staying water that will come from the pipelines. Once the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Before proceeding to fit the new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the tub in the called for placement. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the tub up until the spirit level reviews degree.
To install faucets, fit the bottom of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water as well as check all joints and also brand-new pipework for leakages and tighten them if required. Fill up the bath tub and likewise examine the overflow electrical outlet and the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub ought to wait till the tub has actually been made use of at the very least once as this will certainly settle it into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type needs to be linked to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall surface between the bathroom and also the tiling, leading to problems with moisture and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can crack fairly very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the market. It is recommended to fit the ceramic tiles using water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that editorial about How to Install a Bathtub through someone on another web blog. Sharing is good. Helping others is fun. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
Hot water issue? Call!